Product ID:EA 956 PART B
MSDS Date:12/13/1989
FSC:8040
NIIN:01-126-6271
Kit Part:Y
MSDS Number: BJKQT

DEXTER ADHESIVES & STRUCTURAL MATERIALS

2850 WILLOW PASS ROAD
PITTSBURG, CA 94565
US

Emergency Phone: 415-687-4201

Info Phone: 415-687-4201

Cage: 33564

DEXTER CORPORATION ADHESIVE & COATING SYSTEMS

312 BAY POINT, CA 94565-3299 US

Telephone: 202-483-7616

Cage: 33564

EPOXY RESIN SYSTEM

DIETHYLENE TRIAMINE

CAS: 111-40-0

RTECS: IE1225000

Fraction By Weight: <15%

OSHA PEL 1 PPM

ACGIH TLV: S, 1 PPM; 9192

VOC LESS THAN 10 GAL/LITER ESTIMATED.

RTECS: 9999999VO

Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Health Hazards Acute and Chronic:MATERIAL IS CORROSIVE TO SKIN. MAY
CAUSE CHEMICAL BURNS TO SKIN AND SEVERE BURNS TO EYES. VAPORS ARE
IRRITATING AND MAY CAUSE CHEST DISCOMFORT AND BRONCHITIS SYMPTOMS.
Explanation of Carcinogenicity:N/K. * FAILURE TO OBSERVE CAUTION MAY
RESULT IN EXCESSIVE HEAT.
Effects of Overexposure:POSSIBLE BURNS TO EYES AND SKIN: IRRITATION AND
POSSIBLE SENSITIZATION TO SKIN. VAPORS IRRITATING TO UPPER
RESPIRATORY TRACT.

First Aid:FLUSH SKIN AND EYE CONTACT WITH PLENTY OF WATER. WASH
THOROUGHLY WITH SOAP AND WATER, RUBBING ALCOHOL OR HAND CLEANER. DO
NOT USE SOLVENTS. REMOVE SOILED CLOTHING AND WASH BEFORE REUSE. IF
IRRITATION PERSISTS, SEE A PHYSICIAN.

Flash Point Method:TOC
Flash Point:>300F,>149C
Extinguishing Media:DRY CHEMICAL OR HALON FIRE EXTINGUISHER, WATER
SPRAY, FOAM OR FOG.
Fire Fighting Procedures:USE SELF-CONTAINED BREATHING APPARATUS WHEN
FIGHTING FIRES IN CONFINED AREAS.
Unusual Fire/Explosion Hazard:DENSE SMOKE AND TOXIC GASSES MAY BE
LIBERATED

Spill Release Procedures:WEAR PROTECTIVE CLOTHING, GLOVES AND SAFETY
GLASSES. SCRAPE UP AND TRANSFER TO METAL CONTAINER. WIPE UP
REMAINING RESIDUE WITH SOLVENTS, OBSERVING SOLVENT FLAMMABILITY
CAUTIONS.

Handling and Storage Precautions:USE ONLY IN A WELL VENTILATED AREA.
STORE AT ROOM TEMPERATURE (77 DEG. F) FOR 12 MONTHS.
Other Precautions:FOLLOW RECOMMENDED CURING SCHEDULE.

Respiratory Protection:NOT NEEDED WITH GOOD INDUSTRIAL VENTILATION.
Ventilation:LOCAL EXHAUST RECOMMENDED.
Protective Gloves:IMPERVIOUS PLASTIC OR RUBBER GLOVES.
Eye Protection:SAFETY GLASSES OR GOGGLES.
Other Protective Equipment:AS NEEDED TO PROTECT SKIN AND CLOTHING.
Work Hygienic Practices:DO NOT GET ON SKIN OR CLOTHING. REMOVE
CONTAMINATED CLOTHING AND THOROUGHLY CLEAN BEFORE REUSE.
Supplemental Safety and Health
DO NOT HANDLE OR USE UNTIL THE MSDS HAS BEEN READ AND UNDERSTOOD.

Boiling Pt:B.P. Text:DECOMPOSES
Vapor Density:NEGLIGIBLE
Spec Gravity:>1
Evaporation Rate & Reference:NEGLIGIBLE
Solubility in Water:NEGLIGIBLE
Appearance and Odor:AMBER LIQUID WITH AMMONIACAL ODOR.

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS, STRONG LEWIS OR MINERAL ACIDS.
Hazardous Decomposition Products:CO, NOX, ALDEHYDES, ACIDS AND
UNDETERMINED ORGANICS
Conditions to Avoid Polymerization:AVOID MIXING RESIN/CURING AGENTS IN
BATCHES >1 LB TOTAL. DON'T HEAT MIXED ADHESIVE UNLESS CURING
SURFACE TO BE BONDED.*

Waste Disposal Methods:DISPOSE OF AS HAZARDOUS WASTE ACCORDING TO
FEDERAL, STATE AND LOCAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.